#Stampin up perfect layers full
#Stampin up perfect layers series

Layers attached to the DSP are die cuts in Garden Green card stock, Lovely Layers Vellum, Soft Suede, and the berries are die cut from 2022-2024 In Color 6×6 Glimmer Paper, Sweet Sorbet. The next is a grouping created on the 2022-2024 In Color 6×6 DSP (Sweet Sorbet). Adhere to sentiment label.Īdd some Brushed Metallic Adhesive Backed Dots.The card base as you can see, is Parakeet Party with a die cut in the same color die cut with Candy Canes Dies and adhered to the card base with liquid glue. Adhere to tag and then adhere to card with Dimensionals.Ĭut bow (from Country Wreaths Dies) from a scrap of Gold Foil Sheet and adhere to top of tag.Ĭut 2 small branches from Evening Evergreen Cardstock and 1 small branch from Soft Succulent Cardstock using the Holly Berry Dies. I chose this sentiment because it fit nicely on the tag. Stamp sentiment (from Penguin Place Stamp Set) with Evening Evergreen Ink on a 1 1/4 x 1 1/4 square of Basic White Cardstock. Punch a piece of Soft Succulent Cardstock using the Essential Tag Punch.

Soft Succulent Cardstock - 5 1/4 x 2, adhere to center of card.īasic White Cardstock - 5 1/4 x 1 3/4, emboss using the Pine Bough Embossing Folder from the Wintry 3D Embossing Folders.

#Stampin up perfect layers series

Lay pieces on tag to determine placement and adhere each piece.įeed piece of Glittered Organdy Ribbon through top of tag and tie a bow with a piece of twine.Īdhere to tag to the card putting your adhesive behind the pieces so it doesn’t show through.Įvening Evergreen Card Base - 5 1/2 x 8 1/2, score at 4 1/4īoughs Of Holly Designer Series Paper - 5 1/4 x 4 (you can use two 5 1/4 x 1 strips if you want to save on paper) Adhere to card base. Cut each piece at an angle.Ĭut 3 snowflakes from Coastal Cabana Cardstock. Cover the part you don’t want with Post-It Tape, ink it with Versamark and then remove the tape and stamp. I stamped each part of the sentiment separately leaving space between. Stamp sentiment with Versamark Ink on 1/2” strip of Basic Black Cardstock. Color brim with Coastal Cabana Stampin’ Write Marker and nose with Pumpkin Pie Stampin’ Blends Marker.Ĭut snowman and hat with coordinating dies. Stamp snowman with buttons, face, glasses and hat with Black Memento Ink on scrap of Basic White Cardstock. I did this on scrap paper first and then used it as a template. Snowflake Specialty Vellum - 4 x 3 1/4, cut off top corners to make tag.

#Stampin up perfect layers full

I had to run it through my machine twice to get the full layer embossed. Adhere with Dimensionals.Ĭoastal Cabana Layer - 5 1/4 x 4, adhere to the card.īasic White Layer - 5 1/8 x 3 7/8, emboss using the Wintry 3D Embossing Folder. Stamp sentiment with Starry Sky Ink on a 1/2” strip of Basic White and punch each end using the Banners Pick A Punch. When you adhere the stamped image make sure it hangs a little below the Glimmer Paper so the bottom edge is covered by the frame to give it a clean look.Īdhere the frame around the Glimmer Paper. The staff was colored with Dark Crumb Cake.Īdhere Glimmer Paper to card base and then adhere stamped image to it. I used Dark Balmy Blue for Mary’s veil, Dark Mossy Meadow for Joseph’s head piece Light Crumb Cake for his clothes. I used Dark Daffodil Delight for the star and added some Wink Of Stella. Stamp image on Basic White Cardstock with Starry Sky Ink.Ĭolor image with Stampin’ Blends. Starry Sky Glimmer Paper - cut using the Fabulous Frams Dies (for the inside piece) Starry Sky Cardstock - cut using the Fabulous Frames Dies (for the frame) Thick Basic White Card Base - 5 1/2 x 8 1/2, score at 4 1/4 Adhere flower to white square.Īdhere square to the card using Dimensionals. I used Poppy Parade for the flower and Mossy Meadow for the leaves and then added a little Night of Navy to the small flowers using a cotton swab.Īdhere the white square to the black square. Color the flower with Soft Pastels using Sponge Daubers. Stamp the large floral image with Black Memento Ink and cut with coordinating Die. Clean the stamp and then repeat only cover the Happy part. I used Post-It Tape to cover the Birthday, inked the Happy part, took off the Post-It Tape and stamped it. Lay them on the white layer leaving a border around the outside and adhere them.īasic White - 2 1/2 x 2 1/2, stamp sentiment in top corner with Black Memento Ink. Basic Black Card Base - 5 1/2 x 8 1/2, score at 4 1/4Ĭut 6 pieces of the Designer Series Paper at 2 x 1 3/4.